DESCRIPTION
Part Number: A06B-6087-H130
Description: ALPHA POWER SUPPLY MODULE MDL PSM-30
Product Series: A06B-6087
Control Series: FSi15, FSi16/18/20/21, PowerMate i *Can but used on FS0C, FS15, FS16/18/20/21*
Rated Input: 200-230V, 127 A @200V
50Hz/60Hz 3-phase
Rated Output: 283-325v, 35 kW
Manual No. B-65162
Standard DIN VDE 0160
NAMING CONVENTION:
PSM–(1)(2)(3)(4)
(1)Power supply module
(2)Type: None = power regeneration, R = resistance regeneration, V = voltage conversion type, power regeneration, C = capacitor module
(3)Motor output
(4)Input voltage, None = 200V, HV = 400V
The power supply module provides the main power supply and control power supply. Select a power supply module according to the capacities of the servo motors and spindle motors being used. A single power supply module can be used to drive both the servo and spindle motors provided the capacity of the power supply module is not exceeded.
There are four types of power supply module, as follows:
(1) Power supply module (PSM) This power supply module is designed to provide a main power supply of 200V/230V. The module uses power regeneration that returns energy to the power supply during motor deceleration (regeneration).
(2) Power supply module (PSMR) This power supply module is designed to provide a main power supply of 200V/230V. The module uses resistance regeneration that allows energy to be consumed by resistance during motor deceleration (regeneration). Regenerative discharge unit This unit is a resistance used to consume energy during motor deceleration (regeneration). This unit is required whenever the PSMR is used.
(3) Power supply module (PSM–HV) This power supply module can be connected to a main power supply of 400V/460V without a transformer. The module uses power regeneration that returns energy to the power supply during motor deceleration (regeneration). It is used together with a servo amplifier module (SVM–HV) and spindle amplifier module (SPM–HV) of the 400–V input series. Capacitor module (PSMC–HV) This module is designed for DC voltage smoothing. It is required whenever the PSM–HV is used.
(4) Power supply module (PSMV–HV) This power supply module can be connected to a main power supply of 400V/460V without a transformer. The output voltage is held at 300VDC by a voltage conversion type converter. This unit uses a powe regeneration method that returns energy to the power supply during motor deceleration (regeneration). The module is used together with a servo amplifier module (SVM) and spindle amplifier module (SPM) of the 200V input series. AC reactor unit This unit is a reactor designed for a PSMV–HV. It contains a fuse. The servo amplifier α series is designed to conform to the following European safety standard: DIN VDE 0160 1988/1:1989 (Electronic devices used in a power facility and their incorporation into the facility). To certify conformity to the standard, FANUC has obtained certification from TUV Rheinland, a third–party certification organization for European standards. In power magnetics cabinet design when the machine is to be CE–marked, the installation conditions described in the following sections should be considered carefully, based on the EC Machine Directives (directives based on 89/392/EEC).
CE marking requires compliance with a related EN standard [EN 60204–1] (Electric Devices in Industrial Machines, Part 1: General Requirements). If an EN standard (or an IEC standard if no EN standard exists) exists for a component in the machine, the component must conform to that EN standard. At present, however, no EN standard (or IEC standard) is defined for amplifiers. Based on the results of an investigation made by TUV Rheinland, an approved certification organization for the machine directives, FANUC set the above VDE standard as a target standard and designed the servo amplifier α series to conform to the standard. Therefore, this amplifier series satisfies the amplifier requirements for CE marking. The user can use these amplifiers without having to be concerned about safety.
